Salt-Based Ion Exchange Softener with Dual Tanks and Dual Valve

Model NO.: YL-II-15


Working Principle: Ion Exchange


Inlet Mode: Pipeline


Material for Resin Tank: Gfrp or Ss304/Ss316


Hardness of Effluent Water: ≤0.03mmol/L


Operating Ambient Temperature: 1°c-55°c


Iron Content: ≤0.3mgl/L


Control for Regeneration: Time Based or Flow Rate Based


Trademark: YLD


Origin: Jiangyin, China




Installation: Vertical Type


Certification: CE, SGS


Heating Mode: Instant Heat


Hardness of Raw Water: <8mmol/L


Working Temperature: 0.25-0.6MPa


Suspended Solids in Raw Water: ≤0.5mgl/L


Relative Humidity: ≤95%


Control Valve: Runxin,Fleck,Jk ,etc


Specification: to be practical


HS Code: 842121999



Salt-based Ion Exchange Softener With Dual Tanks And Dual Valve



Ion Exchange softener



Water softening happens through a process called ion exchange, which uses an ion exchange resin. The resin comprises of tiny polymeric beads which are specially formulated so that they can be charged with certain ions. Calcium and magnesium, the causes of scale and scum from hard water, are referred to as ions, and as water passes through the resin, the calcium and magnesium ions swap places with the sodium ions on the resin. Sodium salts, unlike calcium and magnesium, are highly soluble so sodium does not cause scale or scum. When all the sodium ions have been exchanged for calcium or magnesium, the resin must be regenerated by recharging it with sodium ions. This is done by flushing the resin with salt solution (brine).





01. By means of Absorbing the calcium and magnesium ions in water with resin, since the hardness of water is mainly composed of calcium and magnesium, in general, we adopt cation exchange resin (softener), replace Ca2+, Mg2+ (main ingredients for scale) in water, as the increase of Ca2+ and Mg2+ in resin, removing performance on Ca2+, Mg2+ of resin will gradually reduce.

02. When the resin has absorbed a certain amount of calcium and magnesium ions, it must be regenerated, the regeneration process is that flush resin layer with the salt water in salt box, replace hardness ion out of the resin again, and discharged from the tank with waste liquid of regeneration, then resin resumed the function of softening and exchanging.

03. The principle of sodium ion exchange and softening treatment is to exchange cation in the raw water with resin, hardness constituents Ca2+and Mg2+ in water exchange Na+ in resin, thus absorb the Ca2+and Mg2+ to make the water to be softened.

2RNa + Ca2+ = R2Ca + 2Na+

2RNa + Mg2+ = R2Mg + 2Na+

After the water treated by sodium ion exchanger, the Ca+ and Mg+ were superseded by Na +.





Type choice:

Softener equipment applies cation resin for softing raw water,its main target is to use cation resin to adsorp (main parts of ),encreasing the hardness of raw water.

1. Users can choose manual operation control system for saving cost.

2. If users using for 24 hours can accord to water using time choosing for rebirth

3. Uses can according to water quality requirement:first grade multi-media filter,which can remove mud,rust,colloid and suspension in water.Second grade activated carbon filter,which can remove color,olfactory,biochemistry organic in water and encrease the left oxygen value and pollution in water.Third grade equiped softener equipment.

4. Effluent water capacity achieves the water supply of national low-pressure bioler.

5. Time control- type;flow control- type.In working ,apply single-tank,double-tank and multi-tank etc. other varied combination method.When choosing,users can choose as their needs.In operation,it has not only automatic function,but also is manual operation.



AAA:



01.What is the capacity(cubic meter per hou)for this Water Softener?--VERY IMPORTNT for our quotation.



02.What is the working hours for this water softner each day?is it continuous 24 hours working or not?



03.Do you require the whole Water Softener System be assembed and installed into an integrated compact cabinet?

04.if there is no special requirement on valve brand,we will choose top domestic brand valve,



Technical parameters:

Category	Model	Recommended water yield (M³/h)	Tank size Diameter *Height(mm)	Salt box (L)	Amount of resin(KG)
Dual-valve and dual-tank (simultaneous operation and respective regeneration)	YL-II-36	24-36	900×1900	800	1040
	YL-II-50	36-50	1000×2200	1000	1440
	YL-II-70	50-70	1200×2400	1500	2000
	YL-II-100	70-100	1500×2500	2000	3200
Dual-valve and dual-tank(One for use and the other for standby)	YL-II-1	1	250×1400	60	80
	YL-II-2	2	300×1400	100	120
	YL-II-3	3	350×1400	100	160
	YL-II-4	4	400×1650	200	240
	YL-II-5	5	500×1750	300	360
	YL-II-6	6	600×1900	350	480
	YL-II-10	8-10	750×1900	500	720
	YL-II-18	12-18	900×1900	800	1040
	YL-II-25	18-25	1000×2200	1000	1440
	YL-II-35	25-35	1200×2400	1500	2000
	YL-II-50	35-50	1500×2500	2000	3200

Our softeners are effective in:

Preventing scale in the hot water system and around taps

Removing existing scale

Reducing boiler fuel cost and heating system maintenance costs

Preventing soap scum, which is evident around the bath and sink

Improving the texture of laundry by preventing detergent scum deposits within the fibers of clothes, bedding, etc.

Reducing soap and detergent costs.

Contact us if you need more details on Water softener. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Water Filter、Water Treatment. If these products fail to match your need, please contact us and we would like to provide relevant information.

Product Categories : Water Softener > Industrial Water Softener